• b1
  • b1
  • b1
  • b1
  • b1
  • b1
  • b1

Company Products

We are the stockholders of stainless steel sheets/plates, coils, tubes, pipes, round bars and other stainless steel products in all popular grades like 304, 304L, 316L, 309, 310S, 430 from 0.30mm to 50.00mm in finishes 2B, BA, No. 4 (brush), Hair Line, No. 8 (Mirror), No.1, finish, chekered and others in regular sizes, i.e. 4 feet by 8 feet, 5 feet by 10 feet and other demanded sizes in the Gulf. We also have larger sizes like 2000mm x 6000mm, 1500mm x 6000mm in grade 304 and 316L.

GRADES

SIZES 304 316 430
       
4’ X 8’ * * *
4’ X 10’ * * *
5’ X 10’ * *  
1.5M X 6M * *  
2M X 6M * *  
COILS * * *

FINISHES

  304 316 430
       
2B * * *
BA * * *
NO.4 * *  
NO.8 * *  
NO.1 * *  

THICKNESS

  304 316 430
       
0.30MM TO 1.00MM * * *
1.20MM TO 3.00MM (CR) * *  
3.00MM TO 50.00MM (HR) * *  

Stainless Steel Tubes

There is a wide range of round, square and rectangular tubes stocked in grades 304, 304L and 316L for the kitchen equipment manufacturing industry, and also for the Interior decor industry.


Stainless Steel Pipes & Fittings

Industrial Stainless steel pipes & fittings (grade 304, 304L and 316L) are also stocked in wide range as the number of industries in the Entire Gulf are increasing at an exponential rate and they need very prompt supply of the pipes & fittings.


Stainless Steel Long Products

Also available are Long Products in Stainless Steel including: Stainless Steel Round Bars, Stainless Steel Flat Bars, Stainless Steel Angles.

No. 1 Finish

No. 1 Finish: is produced by rolling stainless steel that has been heated prior to rolling (hot-rolling). This is followed by a heat treatment that produces a uniform microstructure (annealing) and ensures that the stainless steel will meet mechanical property requirements. After these processing steps, the surface has a dark non-uniform appearance called “scale”. Surface chromium has been lost during the previous processing steps, and, without removal of the scale, the stainless steel would not provide the expected level of corrosion resistance. Chemical removal of this scale is called pickling or descaling, and it is the final processing step. A No. 1 finish has rough, dull, and non-uniform appearance. There may be shiny spots were surface imperfections were removed by grinding. It is generally used in industrial applications, such as equipment for elevated temperature service.

Applications:

Air heaters, Annealing boxes, Boiler baffles, Carburizing boxes, Crystallizing pans, Firebox sheets, Furnace arch supports, Furnace conveyors, Furnace dampers, Furnace linings, Furnace stacks, Gas turbine parts, Heat exchanger baffles, Heat exchanger tubing supports, Incinerators, Industrial oven liners, Kiln liners, Oil burner parts, Recuperators, Refineries, Tube hangers.

2B Finish

2B Finish: is a bright cold rolled finish commonly produced in the same manner as No. 2D, except that the final light cold rolling pass is done using polished rolls. This produces a more reflective finish that resembles a cloudy mirror. Finish reflectivity can vary from manufacturer-to-manufacturer and coil-to-coil with some coils looking quite mirror-like and others being fairly dull. No. 2B is a general purpose cold rolled finish commonly used for all but exceptionally difficult deep drawing applications. It is more readily polished to high luster than a No. 1 or No. 2D finish.

Applications:

Bakeware, Chemical plant equipment, Dye house equipment, Flatware, Laundry and dry cleaning, Paper mill equipment, Pharmaceutical equipmentPlumbing fixtures, Refrigeration, Sewage treatment, Sheet metal products, Small tanks, Solar collector panels, Vacuum drum dryers, Waste fuel pool liners, Wheel covers.

Bright Annealed

Bright Annealed: is produced by heat-treating (annealing) in a controlled atmosphere furnace. It has a mirror like appearance but may have some cloudiness and other imperfections. A finish that is designated “BA” has only been bright annealed. A finish that is designated “2BA” has been bright annealed and then passed between highly polished rolls. A minimal amount of roll pressure (skin pass) is applied. The process improves flatness and finish uniformity but does not significantly decrease thickness. Bright annealed stainless is sometimes buffed to attain a more mirror-like finish. It is often specified for applications where a highly reflective surface is desired.

Applications:

Appliance trim, Appliances, Architectural components, Auto trim, Builder’s hardware, Chute liners, Commercial refrigerators, Cookware, Fishing equipment, Flatware, Food processing equipment, General hardware, Highway truck trailers, Mass transit cars, Radiant heaters, Range hoods, Scientific apparatus, Surgical instruments, Textile finishing equipment.

No. 4 Finish:

No. 4 Finish: Finish is characterized by short, parallel polishing lines, which extend uniformly along the length of the coil. It is obtained by mechanically polishing a No. 3 finish with gradually finer abrasives. Depending on the requirements of the application, the final finish can be anywhere between 120 and 320 grit. Higher grit numbers produce finer polishing lines and more reflective finishes. The surface roughness is typically Ra 25 micro-inches or less. This general-purpose finish is widely used for restaurant and kitchen equipment, storefronts and food processing and dairy equipment. If a fabricator needs to blend in welds or do other refinishing, the resulting polishing lines are usually longer than on product polished by a producer or toll-polishing house.

Applications:

Appliances, Architectural wall panels, Beverage equipment, Boat fittings, Bus shelters, Clean rooms, Column covers, Dairy equipment, Elevator doors and interiors, Escalator trim, Food processing equipment, Furniture Highway tank trailers, Hospital surfaces and equipment, Instrument or control panels, Kitchen equipment, Luggage handling equipment, Mass transit equipment, Restaurant equipment, Sinks, Sterilizers, Storefronts, Water fountains.

No. 8 Finish

No. 8 Finish: is the most reflective polished finish that is covered by the ASTM standards. It is produced in the same manner as the No. 7 finish except that the buffing is continued for an additional five to ten minutes. In comparison to a No. 7 finish, the grit lines are much less visible, but they can be seen if the finish is examined closely. The resulting finish is mirror-like but not a perfect mirror.

Applications:

Clean rooms, Column covers, Mirrors, Ornamental trim, Press plates, Reflectors, Signage, Wall panels.